PLIOGRIP RESINS & CHEMICALS PVT LTD

Regd office & factory:  Plot No.W-78, Phase-II, MIDC, Dombivili (E), Dist:Thane-421203, Maharashtra,

Factory : Plot No.A/681, T.T.C Industrial area, M.I.D.C, Pawane village, Navi Mumbai– 400705.

Phone : Dombivili : 91-251-2871078 Fax : 91-251-2873498 , Mobile: 09324255435 / 433

Phone : Navi Mumbai: 91-022-27780742 / 29202870 / 29252090  Mobile: 09820078238

 

PLIOGRIP EPOXY RESIN PER 205 AND PLIOGRIP HARDENER PH 105 FOR HAND LAY-UP APPLICATION

 

 

GENERAL DESCRIPTION

 

PLIOGRIP EPOXY RESIN PER 205 is an unmodified liquid epoxy resin of medium viscosity that can be used with an aliphatic amine hardener PH 105 for hand lay-up applications. PLIOGRIP PH 105 is a low viscosity room temperature curing liquid hardener. This system gives a short pot life and fast cured at normal ambient temperatures. Products made from this system can be subjected to working temperature of 100°C.

 

TYPICAL PROPERTIES OF PLIOGRIP EPOXY RESIN PER 205

 

Properties	Values
Type	Unmodified viscous epoxy resin
Specific gravity @ 25°C	1.14 -1.20
Appearance	Clear to pale yellow liquid
Epoxy equivalent	180 - 200
Viscosity @ 25°C (CPS)	9000 - 13000
Chlorine content (max.%)	0.2

 

TYPICAL PROPERTIES OF PLIOGRIP HARDENER PH 105

 

Properties	Values
Type	Aliphatic Amine
Specific gravity @ 25°C	0.95 -1.05
Appearance	Pale yellow liquid
Viscosity @ 25°C (CPS)	20 - 30

 

MIX RATIO (PARTS BY WEIGHT) AND POT LIFE AT 25°C IN MINUTES

 

PLIOGRIP EPOXY RESIN PER 205	PLIOGRIP HARDENER PH 105	POT LIFE
100	10 - 12	45

CURING TIME:

 

Curing temperature °c	30	40	80	100
Curing time	14-24 hrs	6-8 hrs	1-2 hrs	20-30 mins

 

TYPICAL PROPERTIES UNFILLED CURED SYSTEM WITHOUT REINFORCEMENT

 

Properties	Values
Density (gm/cc)	1.15 - 1.20
Tensile strength (kg/cm2)	50 - 60
Compressive strength (kg/cm2)	100 -120
Flexural strength (kg/cm2)	120 -140
Impact strength (kg.cm/cm2)	> 12
Water absorption (% w/w)	less than 0.2
Modulus of elasticity (kg/cm2)	4000- 4500
Martens HDT (0C)	70 - 80
Thermal conductivity (kcal /mh°C)	0.21
Relative dielectric constant @25 °C	4.0
Dielectric loss factor tan 8 @ 25°C	0.003
Volume resistivity (10'5 n cm) @ 25°C	1.2
Tracking resistance (grade)	KA3C
Min. dielectric strength (kV/cm)	190 -210

 

SAEFTY PRECAUTIONS:

 

Direct contact of Resin/Hardener with skin should be avoided. Use of hand gloves while handling them is recommended. Splashes on the skin, if any, should be removed immediately with soap and lukewarm water or with a suitable remover.

 

STORAGE:

Should be stored in closed containers in cool condition away from direct sunlight. Shelf life of Resin & Hardener @ 25°C is about 18 months from the date of manufacturing.

 

 

NOTE:

The information given in this literature is based on the present state of our knowledge but any conclusions and recommendations are made without any liability on our part. Buyers and users should make their own assessment of our products under their own conditions and for their own requirements.